Tablet Press

Tablet Press

Formulation Of Acetylsalicylic Acid Tablets For Aqueous Enteric Film Coating

 The goal of this study was to determine which combination of excipients would result in a tablet core that would be suitable for use in an aqueous enteric film coating process. A relatively simply formulation of microcrystalline cellulose (MCC) and partially pregelatinized starch (P-PGS) was found to provide the necessary properties. MCC in the formulation provided the compactability needed to produce a tablet that will withstand the mechanical stresses of the film-coating process. P-PGS provides the dissolution characteristics and is responsible for the stability characteristics in this moisture sensitive, enteric film-coated application. It was also found that P-PGS could be used to reduce the deleterious effects of superdisintegrants in formulations.

 

In recent years, acetylsalicylic acid (ASA; also well known as aspirin) has been prescribed for a host of indications. In addition to its uses as an analgesic, anti-inflammatory and antipyretic agent, ASA is no indicated for use in the prevention and treatment of heart disease and stroke. Further studies are currently under way investigating the potential of ASA for bolstering the immune system, treating cognitive decline and lowering the risk of colon and ovarian cancer. A low daily dose, 75-81 mg, is commonly used in preventative ASA therapy. Historically, ASA has been regarded as a potential gastric irritant(1) and studies have shown that the incidence of gastric intestinal side-effects may increase with regular use(2) Enteric coating of the tablets is therefore desirable for preventing stomach upset or irritation in those taking daily ASA therapy.

 

Aspirin is a moisture sensitive drug and can hydrolyse into acetic and salicylic acids when exposed to high humidity and elevated temperatures(3). As the coating process will subject ASA tablets to both high temperatures and humidity, it is important that the formulation is resistant to moisture interaction. Mitrevej and Hollenbeck found that a hydrophilic field is generated around ASA crystals under high humidity conditions and that upon combining the ASA with certain hydrophilic disintegrants, condensation in the vicinity of the ASA crystal can occur(4). The disintegrants studied were sodium starch glycolate (SSG), croscarmellose sodium (CCS), crospovidone and colloidal silica. During the aqueous film-coating process, Faroongsarng and Peck determined that the depth of water penetration in the tablet core could be directly linked to the concentration and type of disintegrant used in the formulation(5). Further work by Bashar Al-Taani studying aqueous coating solutions for ASA tablets confirmed that the moisture penetration during the coating process was not only formulation dependent but could be directly linked to the stability of the final coated ASA tablet(6).

 

A review of ingredients contained in five commercially purchased ASA products found that, in most cases, the primary listed excipients were microcrystalline cellulose (MCC) and some form of starch. The use of additional excipients including disintegrants (such as CCS and SSG), lubricants and glidants varied. All five products were packaged in foil sealed high density polyethylene (HDPE) bottles, three of which contained carbon/silica desiccant packs. The goal of this study was to determine which combination of excipients, found in commercial ASA products, would result in a tablet core that would be suitable for use in an aqueous enteric film-coating process. The ideal enteric coated tablets would need to exhibit excellent stability under accelerated storage conditions without the fuse of extra (and more costly) packaging precautions such as desiccant packages for other specialized packaging materials.

Material and Equipment

Aspirin 1040 (Aspirin USP 40-mesh crystals, Rhodia, Cranbury, New Jersey, USA) was used as the active material. The excipients used in the study were partially pregelatinized starch (P-PGS) (Starch 1500, Colorcon, West Point, Pennsylvania, USA); MCC (Emcocel 50M, Penwest, Patterson, New York, USA); SSG (Explotab, Penwest);CCS (Ac-Di-Sol, FMC, Princeton, New Jersey, USA) and stearic acid NF (purified vegetable grade powder, Oleotec Ltd, London, UK). The packaging materials used were 85 mL foil-sealable HDPE bottles (Drug Plastics and Glass Co., Boyertown, Pennsylvania, USA) and desiccant packs (3964, Sud-Chemie Performance Packaging, Belen, New Mexico, USA). The coating materials used were an aqueous enteric coating system (Opadry II), both manufactured by Colorcon.

 

Ingredients were dry blended in a 16-quart twin-shell blender (Patterson-kelley Co., East Stroudsberg, Pennsylvania, USA). Tablets were compressed on an instrumented 10-station Piccola rotary press (Riva, Buenos Aires, Argentina). Tablet hardiness was measured using a Multichek tester (Erweka, Milford, Connecticut, USA). A side-vented 15 in. coating pan (Labcoat II, O’Hara Technologies, Toronto, Canada) was used to apply the coatings. A dissolution test station (VK 7010, apparatus I, VanKel, Cary, North Carolina, USA) was used for drug release testing. An HPLC (high performance liquid chromatography system (Alliance 2690, Waters Corp., Milford, Massachusetts, USA) was used to determine free salicyclic acid concentration.

Methods

Blending and Tablet Preparation

Six formulations (see Table I), composed of constant levels of ASA and lubricant and varying levels of MCC, P-PGS, CCS and SSG were each dry blended for 15 minutes in the twin-shell blender. The batch size of each blend was 5kg. Each of the six blends was then compressed on the 10-station rotary tablet press with 7.0 mm standard concave tooling. The target tablet weight was 162.0 mg and the compaction force was adjusted to produce tablets with a breaking force of 6.0-7.0 kp. The tablet coating was performed in a 15 in. side-vented pan equipped with one spray-gun. The pan load was 3kg. A subcoat of Opadry II dispersed in water (15% w/w) was applied to obtain a theoretical 2% tablet weight gain to tablets from all of the six batches. The subcoat applications was immediately followed by an enteric coat of consisting of Sureteric dispersed in water (15% w/w) and applied to obtain a theoretical 10% weight gain. A topcoat of Opadry II dispersed in water (15% w/w) was then applied to the tablets to obtain a 2% weight gain. All six coating trials were conducted using the same recommended process temperatures, spray rates, and operating conditions. In general, the use of a subcoat beneath the enteric coating is optional and largely depends on the quality of the tablet core. As the six batches contained varying ingredients, a subcoat was applied to all six batches so that the enteric layer would be unaffected by minor changes in the tablet surface. The use of a topcoat is optional as well but many commercial products have a topcoat applied to colour the core.

Dissolution and Free Salicylic Acid Testing

The dissolution and free salicylic acid tests were performed according to the USP 23 monograph for ASA tablets. The coated tablets were tested according to the USP 23 monograph for delayed-release ASA tablets.

 

Tablet Hardness Testing

The uncoated tablets were tested for diametrical breaking force before and after storage at accelerated conditions. The average result was reported from 20 tablets tested.

Packaging and Stability

Samples of the uncoated tablets from each formulation were packaged in HDPE bottles (120 tablets per bottle). The coated tablets from each formulation were packaged in the same manner: one set of samples was packaged without desiccant; a second set of samples was packaged with a desiccant pack in each bottle. All bottles were induction (foil) sealed and stored under accelerated conditions- 40 degrees Celcius/75% relative humidity (RH) for 3 months.

 

Results and Discussion

Uncoated ASA Tablets

The dissolution testing conducted in acetate buffer (pH=4.5) revealed that only batch A containing MCC alone as the excipient failed to achieve 80% drug release in less than 20 min. The dissolution results after storage under accelerated conditions showed little change from the initial tests.

 

More significant were the results of the tablet mechanical strength after exposure to accelerated temperature and humidity conditions. The tablets containing just ASA and MCC lost 8.57% in tablet hardness, whereas the tablets containing the MCC-P-PGS combination showed the least decrease in tablet hardness, with a 3.0 % loss. The use of either CCS or SSG in combination with MCC resulted in a loss of more than 36.3 % in tablet mechanical strength. Interestingly, when the same levels of CCS or SSG were used in the tablets that combined P-PGS and MCC, the loss in tablet hardness was less profound. When comparing the levels of free salicyclic acid in uncoated tablets, at the initial time point and after 3 months at 40 degrees Celcius/75% RH, the results showed a similar trend to the tablet hardness results.

 

The USP limit for free salicylic acid in coated ASA tablets is not more than 0.3%. After 3 months in accelerated conditions, the tablets containing just MCC as the excipient or MCC with either CCS or SSG exhibited significantly increased levels of free salicyclic acid and failed to meet the USP requirements. The MCC-P-PGS combination showed virtually no degradation of the ASA with time in adverse storage conditions, and the increase in free salicylic acid was negligible.

 

It has been shown that the P-PGS used in this study has a lower propensity for moisture uptake than either CCS or SSG and will draw less moisture into a tablet under elevated humidity conditions(7). This may account for some of the positive effects seen with its use in this formulation. The data also suggest that P-PGS may be able to trap or retain moisture within the formulation, thus retarding moisture interaction with the ASA.

Initial results for the coated ASA tablets

After coating, the tablets from all of the formulations had a good appearance. None of the tablets exhibited any signs of defects either during or after the coating trials. Tablets from all the batches passed the acid phase of dissolution testing with no release of ASA after 2 hours in 0.1 N HCL. During the buffer phase of testing (pH=6.80, as with the uncoated tablet dissolution results, only the tablets containing just MCC and ASA failed to meet the USP specification of not less than 80% ASA released in 90 min. In fact, the other five formulations attained 80% ASA release in less than 20 min.

 

Coated tablet Stability Results

After 3 months of storage at 40 degrees Celcius/75% RH, some of the tablets containing CCS or SSG exhibited softening of the film coating and sticking of the tablets to one another within the HDPE bottles. This occurred in the samples that were packaged both with and without desiccant packs. Any tablets exhibiting signs of defects at this point were considered stability failures.

 

The free salicylic acid results for the coated tablets were very similar to those results obtained for the uncoated tablets. The USP limit for the free salicylic acid in coated ASA tablets, 3.0%, is higher than the uncoated tablet specification. After 3 months in accelerated conditions, the tablets containing just MCC as the excipient exhibited higher, but acceptable, free salicylic acid levels. The combination of the MCC with CCS or SSG resulted in substantial increases to more than 5.0% free salicylic acid overall, so failed to meet the USP requirements. Again, the most acceptable results were seen for tablets containing MCC and P-PGS as the excipients, which showed no increase in free salicyclic acid when desiccant was used and only a 0.91% increase when packaged without desiccant. The addition of P-PGS substantially reduced the amount of ASA degradation in those tablets containing MCC combined with either SSG or CCS, which had unacceptable free salicylic acid levels.

 

It was interesting to note that the addition of desiccant packs to the bottles was not sufficient to eliminate, or even substantially reduce, the adverse effects of the superdisintegrants. Of the six formulations, the tablets containing MCC alone or the MCC-P-PGS excipient combination met the desired stability performance requirements of good appearance, acid resistance and acceptable free salicylic acid levels. The formulation with just MCC did not meet the delayed dissolution requirements for ASA release in buffer either initially or after 3 months of storage, in accelerated conditions. The tablets containing the MCC-P-PGS combination did exhibit excellent delayed release dissolution results initially and after 3 months at 40 degrees Celcius/75% RH.

 

Conclusions

The results obtained in this study have yielded a relatively simple ASA formulation utilizing a combination of MCC and P-PGS as the primary excipients. MCC in the formulation provides that compactability needed for producing a tablet that will withstand the mechanical stresses of the film-coating process. Starch provides the necessary dissolution characteristics in this moisture sensitive, enteric film-coated application. The formulation without the use of additional superdisintegrants would be well suited to the aqueous film-coating process, and the final coated tablets would not require the use of any specialized packaging materials. It was also found that P-PGS could be used to reduce the deleterious effects of superdisintegrants in formulations. This would also reduce raw material costs. The next phase of this study will focus on optimization of the necessary enteric coating levels and the scale-up of the enteric coating process.

 

Acknowledgements

The authors gratefully acknowledge Rhodia Inc. for the donation of the ASA used in this project. In addition, we thank Mr. David Ferrizzi of Colorcon for his analytical support.

Article reprinted from the May 2001 issue of Pharmaceutical Technology Europe. Reprint publication number: 0462. To see accompanying tables and figures, please visit http://www.colorcon.com/literature/marketing/ex/Starch 1500/enteric_articlenc.pdf.

References

1. B.K. Martin, “The Formulation of Aspirin,” in H.S. Bean, A. H. Beckett and J.E. Carless, Eds, Advances in Pharmaceutical Sciences, Vol. 3(Academic Press, London, UK, 1971) p. 148.
2. R.C Batterman, “Comparison of Buffered and Unbuffered Acetylsalicylic Acid,” New Engl. J. Med. 258, 213-219 (1958).
3. Merck Index, Twelfth Edition, 886, Merck Research Laboratories (1996).
4. A. Mitreveg and R.G. Hollenbeck, “Influence on Hydrophylic Excipients on the Interaction of Aspirin and Water,” Int. J. Pharm. 14, 243-250 (1983).
5. D. Faroongsarng and G. Peck, “The Swelling of Core Tablets during Aqueous Coating I: A Simple Model Decribing Extent of Swelling and Water Penetration for Insoluble Tablets Containing a Superdisintegrant,” Drug Dev. Ind. Pharm. 17(18) 2439-2455 (1991).
6. B. Al Taani, “Physical Interactions of Aqueous Coating Solutions with Tablet Cores Containing Superdisintegrants during Pharmaceutical Aqueous Coatings,” Doctoral Thesis, Department of Industrial and Physical Pharmacy, Purdue University, West Lafayette, Indiana, USA (May 1999).
7. C. Cunningham, “Maize Starch and Superdisintegrants in a Direct Compression Formulation,” Pharm. Manufac. Rev. 22-24 (December 1999).

 

 

About Colorcon®

Colorcon® is a world leader in the development, supply and technical support of formulated coatings and excipients for the pharmaceutical industry. With Colorcon as their pharmaceutical product development partner, companies produce cost effective, high quality products with superior performance and appearance. To learn more, please visit http://www.colorcon.com/.

 

 

About the Author

Charles R. Cunningham and Bruce R. Kinsey are global technical managers. Laura K. Scattergood is an applications technologist. All are in global technical support at Colorcon® in West Point, Pennsylvania.

Tablet Press $60.54 High Quality Content by WIKIPEDIA articles A tablet press is a mechanical device that compresses powder into tablets of uniform size and weight. A press can be used to manufacture tablets of a wide variety of materials, including pharmaceuticals, illicit drugs such as MDMA, cleaning products, and cosmetics. To form a tablet, the granulated material must be metered into a cavity formed by two punches and a die, and then the punches must be pressed together with great force to fuse the material together. Author: Surhone, Lambert M./ Tennoe, Mariam T./ Henssonow, Susan F. Binding Type: Paperback Number of Pages: 68 Publication Date: 2010/12/04 Language: English Dimensions: 6.00 x 9.02 x 0.16 inches

Press On $11.49 Press On

Tablet and Capsule Machine Instrumentation $240 A combination of a sound formulation with a proper control of the tabletting or capsule filling process is necessary to produce a satisfactory tablet or capsule. These considerations require accurate measurements. Tablet and Capsule Machine Instrumentation is a practical guide to the techniques and applications of instrumentation used to make these measurements. The text provides a sound understanding of the principles and techniques involved, and of how data generated by instrumented machines can be applied to problems in pharmaceutical research, development and manufacture. Topics covered include: the measurement of force; the installation of strain gauges; the measurement of displacement; power supplies and data acquisition; instrumented tablet presses; calibration of transducer systems; data handling; applications of tablet press instrumentation; the instrumentation of capsule filling machinery; automatic control of tablet presses in a production environment. This is an invaluable guide for pharmaceutical scientists and academics involved in pharmaceutical technology research.

Joystick-It Tablet Arcade Stick $24.99 Add a physical joystick to your tablet computer, for enhanced gaming precision! Works with thousands of different games! More precise movement and faster response time. Removable and repositionable. Will not harm your screen. Bring your tablet-based gaming to the next level with the Joystick-It Tablet Arcade Stick! The Joystick-It gives you a real physical joystick, for increased precision with touch-screen based games. Simply press down to attach the Joystick-It to your tablet-based computer's screen for improved gaming. No wires or batteries needed! The Joystick-It works with thousands of different game apps. Any game that has an on-screen control pad of some kind is perfect for the Joystick-It. Simply run your game of choice, place the Joystick-It over the on-screen control pad and push down. The Joystick-It sticks to the glass of your display and is ready for action. The lightweight, solid, milled-aluminum construction of the Joystick-It adds more precise movement and faster response time for enhanced playability! When you're done, simply pull up on the Joystick-It to remove it from the screen. Measures about 2-inches tall.

Press $24.99 Press - Photographic Print

FROG STREET PRESS FST651T SMART START K1 STORY TABLET $20.01 Writing paper based around the Sky to Ground TM concept for handwriting. Bold graphics and colorcoded lines to help your Kindergarteners and First Graders quickly understand the concepts of lines and spaces. Highquality paper makes erasing easy

FROG STREET PRESS FST654T SMART START STORY TABLET $20.01 1/2 STORY TABLET40 SHEETS Writing paper based around the Sky to Ground TM concept for handwriting. Bold graphics and colorcoded lines to help your Kindergarteners and First Graders quickly understand the concepts of lines and spaces. Highquality paper makes erasing easy

FROG STREET PRESS FST653T SMART START 12 WRITING TABLET $20.01 Writing paper based around the Sky to Ground TM concept for handwriting. Bold graphics and colorcoded lines to help your Kindergarteners and First Graders quickly understand the concepts of lines and spaces. Highquality paper makes erasing easy

FROG STREET PRESS FST650T SMART START K1 WRITING TABLET $20.01 Writing paper based around the Sky to Ground TM concept for handwriting. Bold graphics and colorcoded lines to help your Kindergarteners and First Graders quickly understand the concepts of lines and spaces. Highquality paper makes erasing easy

Mead Products 5.77in. x 5.88in. Floral Tablet 79036 Pack of 4 $29.35 Tablet

ThinkPad Tablet $591.6 ThinkPad Tablet

Tablet Speaker $34.99 Tablet Speaker

Memoral Tablet $10.49 Memoral Tablet

Press On Press On $29 Download the Press On Press On font for Mac or Windows in OpenType, TrueType or PostScript format.

Tablet,Midol $35.99 REFILL,TABLET,MIDOL

RF Tablet $212.99 TouchIT RF Tablet

The First Press - a Wine Press $39.99 The First Press - a Wine Press - Giclee Print

Tablet Attaché - for web tablet $22.99 Case Logic Tablet Attaché - Case for web tablet - nylon - tannin - for Apple iPad 1 2

Press The Spacebar $12.49 Press The Spacebar

Press Gang $26.99 Press Gang