Velocity Tablet

Velocity Tablet

Air flow bench

Air pump

The pump used must be able to deliver the volume required at the pressure required. Most flow testing is done at 10 and 28 inches of water pressure (2.5 to 7 kilopascals). Although other test pressures will work, the results would have to be converted for comparison to the work of others. The pressure developed must account for the test pressure plus the loss across the metering element plus all other system losses. The greater the accuracy of the metering element the greater is the loss. Flow volume of between 100 and 600 cubic feet per minute (0.05 to 0.28 m/s) would serve almost all applications depending on the size of the engine under test.

Any type of pump that can deliver the required pressure difference and flow volume can be used. Most often used is the centrifugal dynamic type, which is familiar to most as a vacuum cleaner. Multistaged axial-flow fan types and positive displacement types (piston and rotary) could also be used with suitable provisions for dampening the pulsations. The pressure ratio of a single fan blade is too low and cannot be used.

Metering element

There are several possible types of metering element in use. Flow benches ordinarily use three types: orifice plate, venturi meter and pitot/static tube, all of which deliver similar accuracy. Most commercial machines use orifice plates due to their simple construction. Although the venturi offers substantial improvements in efficiency, its cost is higher

Instrumentation

Air flow conditions must be measured at two locations, across the test piece and across the metering element. The pressure difference across the test piece allows the standardization of tests from one to another. The pressure across the metering element allows calculation of the actual flow through the whole system.

The pressure across the test piece is typically measured with a U tube manometer while, for increased sensitivity and accuracy, the pressure difference across the metering element is measured with an inclined manometer. One end of each manometer is connected to its respective plenum chamber while the other is open to the atmosphere.

Ordinarily all flow bench manometers measure in inches of water although the inclined manometer's scale is usually replaced with a logarithmic scale reading in percentage of total flow of the selected metering element which makes flow calculation simpler.

Temperature must also be accounted for because the air pump will heat the air passing through it making the air down stream of it less dense and more viscous. This difference must be corrected for. Temperature is measured at the test piece plenum and at the metering element plenum. Correction factors are then applied during flow calculations. Some flow bench designs place the air pump after the metering element so that heating by the air pump is not as large a concern.

Additional manometers can be installed for use with hand held probes, which are used to explore local flow conditions in the port.

Flow bench data

The air flow bench can give a wealth of data about the characteristics of a cylinder head or whatever part is tested.

The result of main interest is bulk flow. It is the volume of air that flows through the port in a given time. Expressed in cubic feet per minute or cubic meters per second/minute.

Valve lift can be expressed as an actual dimension in decimal inches or mm. It can also be specified as a ratio between a characteristic diameter and the lift L/D. Most often used is the valve head diameter. Normally engines have an L/D ratio from 0 up to a maximum of .35. For example a 1 inch diameter valve would be lifted a maximum of 0.350 inch. During flow testing the valve would be set at L/D .05 .1 .15 .2 .25 .3 and readings taken successively. This allows the comparison of efficiencies of ports with other valve sizes, as the valve lift is proportional rather than absolute. For comparison with tests by others the characteristic diameter used to determine lift must be the same.

Flow coefficients are determined by comparing the actual flow of a test piece to the theoretical flow of a perfect orifice of equal area. Thus the flow coefficient should be a close measure of efficiency. It cannot be exact because the L/D does not indicate the actual minimum size of the duct.

A real orifice plate showing how the fluid would actually flow

A theoretical orifice plate showing perfect flow which is used as a standard for comparing the efficiencies of real flows

An orifice with a flow coefficient of .59 would flow the same amount of fluid as a perfect orifice with 59% of its area or 59% of the flow of a perfect orifice with the same area (orifice plates of the type shown would have a coefficient of between .58 and .62 depending on the precise details of construction and the surrounding installation).

Valve/port coefficient is non dimensional and is derived by multiplying a characteristic physical area of the port and by the bulk flow figures and comparing the result to an ideal orifice of the same area. It is here that air flow bench norms differ from fluid dynamics or aerodynamics at large. The coefficient may be based on the inner valve seat diameter, the outer valve head diameter, the port throat area or the valve open curtain area. Each of these methods are valid for some purpose but none of them represents the true minimum area for the valve/port in question and each results in a different flow coefficient. The great difficulty of measuring the actual minimum area at all the various valve lifts precludes using this as a characterisc measurement. This is due to the minimum area changing shape and location throughout the lift cycle. Because of this non standardization, port flow coefficients are not "true" flow coefficients, which would be based on the actual minimum area in the flow path. Which method to choose depends on what use is intended for the data. Engine simulation applications each require their own specification. If the result is to be compared to the work of others then the same method would have to be selected.

Various characteristic measurements used to determine flow coefficients

Using extra instrumentation (manometers and probes) the detailed flow through the port can be mapped by measuring multiple points within the port with probes. Using these tools, the velocity profile throughout the port can be mapped which gives insight into what the port is doing and what might be done to improve it.

Of less interest is mass flow per minute or second since the test is not of a running engine which would be affected by it. It is the weight of air that flows through the port in a given time. Expressed in pounds per minute/hour or kilograms per second/minute. Mass flow is derived from the volume flow result to which a density correction is applied.

With the information gathered on the flow bench, engine power curve and system dynamics can be roughly estimated by applying various formulae. With the advent of accurate engine simulation software, however, it is much more useful to use flow data to create an engine model for a simulator.

Determining air velocity is a useful part of flow testing. It is calculated as follows:

For one set of English units * UNITS for SI or English are wrong, different results on conversion!-(The English formula is Verified correct. See ref.)

Where:

V = Velocity in feet per minute

H = Pressure drop across test piece in inches of water measured by the test pressure manometer

d = density of air in pounds per cubic foot (0.075 pound per cubic foot at standard conditions)

For SI units

Where:

V = Velocity in meters per second

H = Pressure drop across test piece in pascals measured by the test pressure manometer

d = density of air in kilograms per cubic meter (1.20 kilograms per cubic meter at standard conditions)

This represents the highest speed of the air in the flow path, at or near the section of minimum area (through the valve seat at low values of L/D for instance).

Once velocity has been calculated, the volume can be calculated by multiplying the velocity by the orifice area times its flow coefficient.

Limitations

A flow bench is capable of giving flow data which is closely but not perfectly related to actual engine performance. There are a number of limiting factors which contribute to the discrepancy.

Steady state flow vs dynamic flow

A flow bench tests ports under a steady pressure difference while in the actual engine the pressure difference varies widely during the whole cycle. The exact flow conditions existing in the flow bench test exist only fleetingly if at all in an actual running engine. Running engines cause the air to flow in strong waves rather than the steady stream of the flow bench. This acceleration/deceleration of the fuel/air column causes effects not accounted for in flow bench tests.

Comparison of flow bench test pressure to actual engine pressures predicted by an engine simulation program

This graph, generated with an engine simulation program, shows how widely the pressures vary in a running engine vs. the steady test pressure of the flow bench.

(Note, on the graph, that, in this case, when the intake valve opens, the cylinder pressure is above atmospheric (nearly 50% above or 1.5 bar or 150 kPa). This will cause reverse flow into the intake port until pressure in the cylinder falls below the ports pressure).

Pressure differential

The coefficient of the port may change somewhat at different pressure differentials due to changes in Reynolds number regime leading to a possible loss of dynamic similitude. Flow bench test pressure are typically conducted at 10 to 28 inches of water (2.5 to 7 kPa) while a real engine may see 190 inches of water (47 kPa) pressure difference.

Air only vs mixed gas/fuel mist flow

The flow bench tests using only air while a real engine usually uses air mixed with fuel droplets and fuel vapor, which is significantly different. Evaporating fuel passing through the port-runner has the effect of adding gas to and lowering the temperature of the air stream along the runner and giving the outlet flow rate slightly higher than the flow rate entering the port-runner. A port which flows dry air well might cause fuel droplets to fall out of suspension causing a loss of power not indicated by flow figures alone.

Bulk flow vs flow velocity

Large ports and valves can show high flow rates on a flow bench but the velocity can be lowered to the point that the gas dynamics of a real engine are ruined. Overly large ports also contribute to fuel fall out.

Even room temperature vs uneven high temperature

A running engine is much hotter than room temperature and the temperature in various parts of the system vary widely. This affects the actual flow, fuel effects as well as the dynamic wave effects in the engine which do not exist on the flow bench.

Physical and mechanical differences

The proximity, shape and movement of the piston as well as the movement of the valve itself significantly alters the flow conditions in a real engine that do not exist in flow bench tests.

Exhaust port conditions

The flow simulated on a flow bench bears almost no similarity to the flow in a real exhaust port. Here even the coefficients measured on flow benches are inaccurate. This is due to the very high and wide ranging pressures and temperatures. From the graph above it can be seen that the pressure in the port reaches 2.5 bar (250 kPa) and the cylinder pressure at opening is 6 bar (600 kPa) and more. This is many times more than the capabilities of a typical flow bench of 0.06 bar (6 kPa).

The flow in a real exhaust port can easily be sonic with choked flow occurring and even supersonic flow in areas. The very high temperature causes the viscosity of the gas to increase, all of which alters the Reynolds number drastically.

Added to the above is the profound effect that downstream elements have on the flow of the exhaust port. Far more than upstream elements found on the intake side.

It is for these reasons that most published information on exhaust port flow is vague. Particularly when concerning how much flow would be required in any given situation. Often quoted is that the exhaust should flow 60% of intake flow but this is only crude guesswork.

Summary

In spite of its limitations the flow bench, in skilled hands, still provides an excellent source of information to guide the engine designer/builder in deciding which modifications to apply to the ports and other components. They are also essential to provide accurate port flow coefficient data that is required for the use of engine simulation software. Together, the air flow bench and engine simulation software provide a powerful microscope to examine the detailed inner workings of running engines. Details which are impossible to view any other way.

Air flow benches are relatively inexpensive to buy and it is fairly simple to build a scientifically valid instrument for home use.

See also

Air flow meter

References

^ Fundamentals of Fluid Mechanics 4th Ed Munson Young -Wiley P514-515

^ Dwyer Air Velocity Instruments manual

External links

Free demo engine simulator used to generate graph above

Plans for a home built flow bench

Forums for those interested in the design and construction of flow benches

Categories: Engine tuning instruments | AerodynamicsHidden categories: Articles needing additional references from September 2007 | All articles needing additional references | Articles that need to be wikified from September 2009 | All articles that need to be wikified
About the Author

I am an expert from China Manufacturers, usually analyzes all kind of industries situation, such as microhardness tester , tablet hardness tester.

Velocity Mirco Cruz Tablet T105 (Full Body) $29.99 Velocity Mirco Cruz Tablet T105 (Full Body)

Velocity Mirco Cruz Tablet T105 (Maximum) $29.99 Velocity Mirco Cruz Tablet T105 (Maximum)

Velocity Mirco Cruz Tablet T105 (Screen) $19.99 Velocity Mirco Cruz Tablet T105 (Screen)

Velocity Micro T103 Cruz Tablet 3.5mm FM Transmitter Car Kit $7.99 Velocity Micro T103 Cruz Tablet 3.5mm FM Transmitter Car Kit

Velocity Micro T301 Cruz Tablet 3.5mm FM Transmitter Car Kit $7.99 Velocity Micro T301 Cruz Tablet 3.5mm FM Transmitter Car Kit

Velocity Micro T301 Cruz Tablet Car Audio Tape Cassette Adapter $4.99 Velocity Micro T301 Cruz Tablet Car Audio Tape Cassette Adapter

Velocity Micro T103 Cruz Tablet Car Audio Tape Cassette Adapter $4.99 Velocity Micro T103 Cruz Tablet Car Audio Tape Cassette Adapter

Velocity Micro T301 Cruz Tablet White 3.5mm Stereo Headset with Microphone $6.99 Velocity Micro T301 Cruz Tablet White 3.5mm Stereo Headset with Microphone

Velocity Micro T103 Cruz Tablet White 3.5mm Stereo Headset with Microphone $6.99 Velocity Micro T103 Cruz Tablet White 3.5mm Stereo Headset with Microphone

Velocity Micro T301 Cruz Tablet Black USB Car Charger $5.99 Velocity Micro T301 Cruz Tablet Black USB Car Charger

Velocity Micro T103 Cruz Tablet Black USB Car Charger $5.99 Velocity Micro T103 Cruz Tablet Black USB Car Charger

Velocity Micro T301 Cruz Tablet White USB Car Charger $5.99 Velocity Micro T301 Cruz Tablet White USB Car Charger

Velocity Micro T103 Cruz Tablet White USB Car Charger $5.99 Velocity Micro T103 Cruz Tablet White USB Car Charger

Velocity Micro T301 Cruz Tablet 3.5mm LED FM Transmitter Car Kit with LCD $14.99 Velocity Micro T301 Cruz Tablet 3.5mm LED FM Transmitter Car Kit with LCD

Velocity Micro T103 Cruz Tablet 3.5mm LED FM Transmitter Car Kit with LCD $14.99 Velocity Micro T103 Cruz Tablet 3.5mm LED FM Transmitter Car Kit with LCD

Velocity Micro T301 Cruz Tablet White LED Clip-On Reading Book Light $5.99 Velocity Micro T301 Cruz Tablet White LED Clip-On Reading Book Light

Velocity Micro T103 Cruz Tablet White LED Clip-On Reading Book Light $5.99 Velocity Micro T103 Cruz Tablet White LED Clip-On Reading Book Light

Velocity Micro T103 Cruz Tablet Universal AC to DC Car Cigarette Lighter Socket Adapter $4.99 Velocity Micro T103 Cruz Tablet Universal AC to DC Car Cigarette Lighter Socket Adapter

Velocity Micro T301 Cruz Tablet USB 2.0 A to Mini-USB B 5-Pin Retractable Cable $4.99 Velocity Micro T301 Cruz Tablet USB 2.0 A to Mini-USB B 5-Pin Retractable Cable

Velocity Micro T103 Cruz Tablet USB 2.0 A to Mini-USB B 5-Pin Retractable Cable $4.99 Velocity Micro T103 Cruz Tablet USB 2.0 A to Mini-USB B 5-Pin Retractable Cable

Velocity Micro T301 Cruz Tablet Black 3.5mm Metal Stereo Headset Handsfree with Microphone $6.99 Velocity Micro T301 Cruz Tablet Black 3.5mm Metal Stereo Headset Handsfree with Microphone

Velocity Micro T103 Cruz Tablet Black 3.5mm Metal Stereo Headset Handsfree with Microphone $6.99 Velocity Micro T103 Cruz Tablet Black 3.5mm Metal Stereo Headset Handsfree with Microphone

Velocity Micro T301 Cruz Tablet Blue 3.5mm Metal Stereo Headset Handsfree Soft Gel Earbud with Microphone $6.99 Velocity Micro T301 Cruz Tablet Blue 3.5mm Metal Stereo Headset Handsfree Soft Gel Earbud with Microphone

Velocity Micro T103 Cruz Tablet Blue 3.5mm Metal Stereo Headset Handsfree Soft Gel Earbud with Microphone $6.99 Velocity Micro T103 Cruz Tablet Blue 3.5mm Metal Stereo Headset Handsfree Soft Gel Earbud with Microphone

Velocity Micro T301 Cruz Tablet LCD (6.25in x 5.10 in) Screen Protector $5.99 Velocity Micro T301 Cruz Tablet LCD (6.25in x 5.10 in) Screen Protector

Velocity Micro T301 Cruz Tablet Black USB Home & Travel Wall Charger $6.99 Velocity Micro T301 Cruz Tablet Black USB Home & Travel Wall Charger

Velocity Micro T103 Cruz Tablet Black USB Home & Travel Wall Charger $6.99 Velocity Micro T103 Cruz Tablet Black USB Home & Travel Wall Charger